60 mhz saw filter 7.8 mhz bandwidth part number SF0060CN02291T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0060CN02291T rev a 9-feb-2010 ecn 36650 page 1 of 3 description ? 60 mhz saw bandpass filter with 7.8 mhz bandwidth. ? 35.1 x 20.6 mm dip package. ? rohs compliant. typical performance horizontal: frequency : 4 mhz/div vertical from top: relative magnitude : 10 db/div relative magnitude : 1 db/div phase linearity : 2 deg/div group delay deviation : 50 ns/div s11 s22
60 mhz saw filter 7.8 mhz bandwidth part number SF0060CN02291T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0060CN02291T rev a 9-feb-2010 ecn 36650 page 2 of 3 specification parameter 1 min typ max units center frequency (fc) 1 59.70 60.00 60.30 mhz 1db bandwidth 2 7.80 8.30 - mhz 3db bandwidth 2 - 8.90 9.20 mhz 55db bandwidth 2 - 11.40 12.20 mhz device delay - 1.85 3.00 us insertion loss (over 1db bw) - 31.5 34 db passband amplitude ripple 3 - 0.30 0.50 db p-p passband phase ripple 3 - 1.5 2.0 deg p-p triple travel and spurious 55 60 db input vswr 4 - 1.3 1.5 :1 output vswr 4 - 1.3 1.5 :1 source and load impedance - 50 - ? ambient temperature - 25 - c notes: 1. average of lower & upper 3 db frequencies. 2. referenced to the insertion loss of the device. 3. defined as the difference between highest and lowest levels over 56.1 to 63.9 mhz. 4. measured at 60 mhz at ambient temperature only. maximum ratings parameter min max units storage temperature range -40 85 ? c operating temperature range -25 85 ? c input power level - 13 dbm matching circuit typical component values: lp1 = 180 nh lp2 = 180 nh (minimum inductor q = 45) rp1 = 68 ? rp2 =68 ? notes: ? suggest the use of 2% tolerance matching components. ? tuning values shown are for reference only. optimum values may change depending upon board layout. input 50 ? single ended output 50 ? single ended 3 15 22 10
60 mhz saw filter 7.8 mhz bandwidth part number SF0060CN02291T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0060CN02291T rev a 9-feb-2010 ecn 36650 page 3 of 3 package outline iso 9001 registered units: mm tolerances are 0.15 mm except for the overall length and width, which are nominal values. pin configuration: input: 3 input ground: 22 output: 15 output ground: 10 case ground: all other pins all specifications are believed to be accurate and reliable. howe ver, spectrum microwave reserves the right to make changes wit hout notice. ? 2010 all rights reserved.
|
